Pin cho iPhone 6S PLUS
Giá bán lẻ đề xuất: 
400.000 VNĐ

Pin thay thế cho Model iphone 6S PLUS

- Được thiết kế chuẩn dung lượng Iphone 6S PLUS

- Áp dụng công nghệ chuẩn pin Li-on Polyme.

- Chuẩn CE Châu Âu, trọng lượng pin nhẹ.

- Chống cháy nổ, an toàn tuyệt đối.

- Dung lượng: 2750 mAh

- Nguyên liệu: Li-ion polymer

- Vòng đời sản phẩm :Trên 1000 lần sạc

Bảo hành 12 tháng lỗi 1 đổi 1

Đặc tính sản phẩm 

Nhãn sản phẩm  battery for iPhone 6SP
Vòng đời sản phẩm / số lần sạc  500 đến 800 lần
Dung lượng tiêu chuẩn 2750 mAh(6.55whr)
Dung lượng thực tế 2750 mAh
Số lần sạc khi sản phẩm xuất xưởng  0 lần
Điện áp vào 3.82V
Điên áp tối đa khi sạc  4.35V
Kích thước  2.8±0.2*38±0.5*96±1mm
Trọng lượng 25.30g
Nhiệt độ lý tưởng khi làm việc   0℃-30℃
Nhiệt độ 6 tháng 
Kích thước hàng hóa nguyên th 30*25*24cm

 

Hướng dẫn thay thế sản phẩm:

Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It's possible to complete the repair without replacing the adhesive, and you probably won't notice any difference in functionality.

Before disassembling your iPhone, discharge the battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

The safest place to pry from is the notch in the front panel above the headphone jack.

​

Twist the spudger to widen the gap between the front panel and the rear case.

​

While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack.

While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display.

Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case.

Insert the flat tip of the spudger under the right edge of the display.

 

Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone.

Pull up on the small nub on the suction cup to remove it from the display.

​

Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.

 

Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone.Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily.

​

Remove two Phillips screws securing the battery connector bracket to the logic board, of the following lengths:

Remove the battery connector bracket.

  •  
  •  

Use a spudger or a clean fingernail to disconnect the battery connector by prying it straight up off the logic board.

 

  •  
  •  

Bend the connector back to ensure it doesn't make contact and power the iPhone on while you're working on it.

 

  •  
  •  

Remove the following Phillips screws:

 

  •  
  •  

Remove the display cable bracket.

 

Be careful to only pry up on the connector itself and not the socket on the logic board.

 

  •  
  •  

Use a plastic opening tool to disconnect the digitizer cable by prying it straight up from its socket on the logic board.

 

Make sure the battery is disconnected before you disconnect or reconnect the cable in this step.

 

  •  
  •  

 

  •  
  •  

Peel back the tips of the three battery adhesive strips along the bottom edge of the battery.

  •  
  •  

Gather the ends of all three adhesive strips in your hand.

  •  
  •  

Gently pull the battery adhesive tabs away from the battery, toward the bottom of the iPhone.

Remove the battery.

Remove the display assembly.

 

*
*
2 + 0 =
Tính các phép tính đơn giản này và nhập kết quả vào. Ví dụ: cho 1+3, hãy nhập 4.